Product Information

Download

FC Tool Download
（Serial Communication Control Software for FC-Series Camera)


Read the contents listed above carefully before decompressing the Download file （FCTool_v100_e.zip）.

(FCTool_v100_e.zip 807KB)

Applicable Cameras

FC-Tool is applicable to cameras which has serial communication function. (FC-series cameras including FC-series color cameras)

FC-series cameras FC-series color cameras
FC11000GE
FC5200GE
FC2200GE
FC1650GE
FC1250GE
FC11000CL
FC5100CL
FC5100PL
FC5100SCL
FC2600CL
FC2000CL
FC2000FCL
FC1600FCL
FC1600FPL
FC1500CL/1500PCL
 FC1500FCL
FC1450UVCL
FC1410CL
FC1410UVCL
FC830FCL
FC830FPL
FC320CL/820CL
FC350CL
FC300ACL
FC2000
FC1500
FC1500F
FC320R/820R
FC300M		 FS11000GE
FS5200GE
FS5000GE
FS2200GE
FS1250GE
FS11000CL
FS5100SCL
FS5100SPL
FS5000HECL
FS2300DV
FS2000HECL
FS350HECL
FS300ACL

* It will be also applicable to each new product launched hereafter.

Usage enviroment
  • Most of our FC-series cameras are equipped with the serial communication feature (*1) and can be connected to the serial port of a personal computer (hereafter referred to as a PC). This software is used to control your camera through a PC by means of serial communication (*2).
  • With this software, almost all of the externally-programmable parameters of an FC-series camera can be operated.
  • This software can be used on the PC that Microsoft Windows XP or Windows 2000 is running on and the .NET Framework (Version 2.0 or later) is installed on. (*3)(*4)
    • （*）
    1. Some models do not support serial communication .（e.g. FC1550MLP／FC1550ML）.
    2. This software uses the RS-232C communication facility of the FC series, or the serial communication facility via the Camera Link (Camera Link)
    3. If you are using the PC that the .NET Framework (Version 2.0 or later) is not installed on or an old version of the .NET Framework has been installed on, it is necessary to install the .NET Framework (Version 2.0 or later) afresh on your PC. The .NET Framework (Version 2.0 or later) can be downloaded from Microsoft’s official website free of charge.
      For details, refer to the “FCTool Installation Procedure” attached separately.
    4. It has been reported that the .NET Framework (Version 2.0 or later) cannot be installed normally on some PCs that Windows 2000 has been installed on.
      For the details on how to install the .NET Framework, see Microsoft’s official website.
    （Note）
    The FCTool may be used only for the purpose of configuring the internal parameters of the FC-series camera by means of serial communication.
    Notice that the software is incapable of displaying the images that it has captured onto the capture board.
    To display the images captured onto the capture board on the PC monitor, use demonstration software released by the manufacturer of the capture board you are using, or the like.
Instruction for use and Indemnity
  1. Use this program only when using our products.
  2. We do not know the program defects at this moment, however, we assume no responsibility whatsoever for any secondary problems along with the program use (malfunction of your computer, data corruption and deletion, etc.). When these problems likely occur, backup the important data or take other countermeasures in advance before using it.
  3. When distributing this program to third parties, contact us in advance.
  4. Do not use this program for other purposes than the setting of our cameras. We shall not be responsible for usage for other purposes than the above and problems caused by the program contents of which is created by entirely or partly copying the original.

Toward top of this page